Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Kelar Yoshakar
Country: Sweden
Language: English (Spanish)
Genre: History
Published (Last): 28 February 2017
Pages: 265
PDF File Size: 14.72 Mb
ePub File Size: 7.96 Mb
ISBN: 634-2-97968-334-1
Downloads: 1420
Price: Free* [*Free Regsitration Required]
Uploader: Dukinos

Last previous edition D — The electrodes shall be wstm after the specimens have been conditioned. It is not intended for the selection of materials.

Breakdown s4066 short-time test, kV All tests shall be conducted on as-molded not annealed specimens conditioned dry-as-molded. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

The designation PAG35 indicates the following: No descriptions are listed unless needed to describe a special grade under the class.

NOTE 12—An example of a special material using this classi? Viscosities for Groups 03, 04, 06, and 08 are measured as described as c4066. A number in parentheses indicates the year of last reapproval. If no properties are speci? These may be speci?

These are electrical limits applied to unreinforced nylons when control of their electrical properties is required. Five specimens shall be tested. These may be specified by using the suffixes as given in Section 5. Inherent viscosity of Group 06 shall be measured on 0. Link to Active This link will always route to the current Active version of the standard.

  INDESIT WIL 62 MANUAL PDF

ASTM D – 94b Standard Classification System for Nylon Injection and Extrusion Materials (PA)

All other grades are listed by requirements. The specimen shall be of sufficient size so that two 4. Some of these compositions are also suitable for compression molding and application from solution. NOTE 6—Materials containing reinforcements or? D — 96a: H Requirements are based on unannealed test specimens 3. zstm

Industrial & Engineering Plastics

It is not intended for the selection of materials. This example can be applied to replace all table values, that is, tensile stress, notched Izod impact, and heat de?

The reinforcement letter designations and associated tolerance levels are shown as follows: Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

  EMOGLOBINA E MIOGLOBINA PDF

This standard does not purport to address all of the safety concerns, if any, associated with its use. Flexural modulus shall be determined on Test Methods D test specimens 6. G Izod impact for these materials shall be conducted on specimens with a D Practice for Sampling of Plastics. NOTE 3—An example of this classi? NOTE 21—Physical properties of most nylon resins are highly dependent upon the moisture content of the molded item.

This example is a general purpose, low viscosity nylon 6 material where U denotes? This section may also include descriptions of the changes or reasons for the changes, or both. Individual specimens shall not be removed from sealed containers until immediately before testing.

A AM — 01a All NOTE 9—An example of this classi? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. It is possible that materials incorporating other pigments or soluble d406, or both may prove adequate for particular applications.

Plastic and Ebonite ISO