AMDGM-M2. Overview · Specification · Gallery · Download · FAQ · Support. Driver Download. Select your OS, Windows MANUAL(1). Manual, Manual for. ECS AMDGM-M2 REV A – Схемы и Service Manual – Другая аппаратура – Материнские платы. Схема,Service Manual Материнские. Official ECS AMDGM-M2 Free Documentation Download Download ECS AMDGM-M2 Driver Update Utility Manual for AMDGM-M2 (PCBx).
|Published (Last):||20 November 2008|
|PDF File Size:||20.37 Mb|
|ePub File Size:||18.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.
Operation am690gm subject to the following conditions: Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered.
ECS AMD690GM-M2 Manuals
Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: Refer to the table below for information: Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface- mount resistors with the clip of the cooling fan.
If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. Pull up the lever away from the socket and lift up to degree angle. Locate the CPU cut edge the corner with the pin hold noticeably missing. Align and insert the CPU correctly.
ECS AMDGM-M2 Free Documentation Download (Official) () –
Installing Memory Modules This motherboard accommodates two or four memory modules. Refer to the illustration below for proper installation: Attach either cable end to the connector on the motherboard.
Attach the other cable end to the SATA hard drive. Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them smd690gm the system bus. Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Amd6990gm that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone, line-in and line-out ports for easier access. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
It elimi- nates limitations of the current Parallel ATA interface. But maintains register com- patibility and software compatibility with Parallel ATA. TPM header Pin No.
New BIOS provides support for new peripherals, improve- ments in performance, or mqnual for known bugs. Install new BIOS as follows: If it fails to find a device, change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the items described below. Boot Other Device Enabled When enabled, the system searches all other possible locations for an operating system if it manuak to find one in the devices specified under the First, Second, and Third boot devices.
Advanced Chipset Features These items define critical timing parameters of the motherboard. You should leave the items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. If you change the values incor- rectly, you may introduce fatal errors or recurring instability into your system. When this item is set to Sync, the following 3 item is activated.
ECS AMD690GM-M2 – 1.0A – motherboard – micro ATX – Socket AM2 – AMD 690G
In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is con- trolled by the power button on your system. If you cannot get a legacy ISA Industry Standard Architecture expansion card to work properly, you might be able to solve the problem by changing this item to Manual, and then opening up the IRQ Resources submenu.
This item displays the PWM value smart fan starts. We strongly recommend you leave this item at its default value. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Below you can find a brief description of each software program, and the location for your motherboard version. Setup Tab Setup Click the Setup button to run the software installation program.
Select from the menu which software you want to install. The following screen appears: Check the box next to the items you want to install. The default options are recom- mended. Click Next run the Installation Wizard. An item installation screen appears: Follow the instructions on maanual screen to install the items. Run Reboot Setup Windows Vista will block startup programs by default when installing drivers after the system restart.
You must select taskbar icon Run Blocked Program and run Amd690m Setup to install the next driver, until you finish all drivers installation. Using the Motherboard Software Then you can restart your computer and continue to install drivers without running blocked programs.
Manuap file in the root directory. Press F10 to save the configuration and exit. The Main Menu screen appears Figure 1. Press ESC to exit. The following screen appears Figure manuall. If so, then this section is not relevant. The following Windows Setup screen appears: The following Windows Setup screen appears listing both drivers:.
Page of 68 Go. Table of Contents Add to my manuals Add. Page 6 Integrated Peripherals Page 12 Memo Introducing the Motherboard Checking Jumper Settings Do not over-tighten the screws as this can stress the motherboard.
Ecs AMDGM-M2 Manuals
Checking Jumper Settings Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Connecting Case Components Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Page 22 Table A: Page 23 Table B: Installing Add-on Cards Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Page 27 Follow these instructions to install an add-on card: Page 57 Click Next.
Page 58 Method 1. Page 59 Select Classic View. Page 63 The Main Menu screen appears Figure 1. Page 65 Press ESC to exit. Page 67 The following Windows Setup screen appears: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.
To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?